check engine AUDI A4 2000 B5 / 1.G ATW Engine On Board Diagnostic Workshop Manual

01-3

Malfunction Indicator Lamp (MIL),
significance

If the ECM recognizes malfunctions that lead to a
worsening of emissions values, it indicates them
by lighting the Malfunction Indicator Lamp (MIL).

Installation location of Malfunction Indicator Lamp (MIL)
The Engine Control Module (ECM) switches on the Malfunction Indicator
Lamp (MIL) after ignition is switched on. Shortly after engine is started,
the exhaust MIL will go out. This requires, first of all, that the Engine
Control Module (ECM) does not detect a malfunction that worsens the
emissions values and, secondly, that activation of the lamp by the Engine
Control Module (ECM) is OK.
If malfunctions that worsen emissions are recognized during operation of
the engine, the ECM switches on the exhaust MIL in instrument cluster.
(These malfunctions are listed in the DTC table). An entry is made in DTC
memory at the same time.
The Malfunction Indicator Lamp (MIL) can blink or remain lit continuously.
DTC memory should be checked in either case Page 01
-16
.
Pa
ge 3 of 19 On Board Dia
gnostic
(OBD
)
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU06.01.1

01-4

Continuously lit:
There is a malfunction that causes increased
emissions. Check DTC memory for Motronic
ECM and automatic transmission (if installed).
Check DTC memory if there is a driveability
problem or a customer complaint, but the
Malfunction Indicator Lamp (MIL) is not lit. There
may be DTCs stored that do not cause the
exhaust MIL to light up immediately, but only
after engine is started again and malfunction is
recognized again.

Blinking:
There is a malfunction that causes damage to
the catalytic converter in this driving condition
(e.g. combustion misfire). In this case, vehicle
must only be driven at reduced power!

Note:
Catalytic converter must be checked after
malfunction is repaired.
Pa
ge 4 of 19 On Board Dia
gnostic
(OBD
)
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU06.01.1

01-7

- Check following wire connection for open circuit
and short circuit to B+:

Test box
VAG1598/31
Socket
Instrument cluster

Terminal
47 Electrical Wiring Diagrams,
Troubleshooting & Component
Locations

- Repair open circuit or short circuit if
necessary.
If wire connection is OK:

- Replace Engine Control Module (ECM) Page
24
-23

Pa
ge 8 of 19 On Board Dia
gnostic
(OBD
)
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU06.01.1

01-8

B- Exhaust MIL remains constantly lit

- Check DTC memory of Engine Control Module
(ECM) Page 01
-16
.
If no DTCs are stored:

- Connect VAG1598/31 test box at wiring harness
to Engine Control Module (ECM), do not connect
ECM Page 24
-19
.

- Remove instrument cluster:

Repair Manual, Electrical Equipment, Repair
Group 90; Instrument cluster, removing and installing


- Check following wire connection for short circuit
to Ground (GND):

Test box
VAG1598/31
Socket
Instrument cluster

Terminal
47 Electrical Wiring Diagrams,
Troubleshooting & Component
Pa
ge 9 of 19 On Board Dia
gnostic
(OBD
)
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU06.01.1

01-10

VAS5051 tester or VAG1551 scan tool,
connecting and selecting functions


Test requirements:

Fuses for engine electronics OK

Electrical Wiring Diagrams, Troubleshooting &
Component Locations

Fuel Pump (FP) relay OK; checking Page 24
-53
.

Battery voltage at least 12.7 V
Ground (GND) connections at engine and
transmission OK

Procedure

Note:
Data Link Connector (DLC) is located in front left knee bolster. - Connect VAS5051 tester to vehicle with VAS5051/1 diagnostic wire.
Alternately, VAG1551 Scan Tool (ST) can also be attached using
VAG1551/3A adapter.
Pa
ge 12 of 19 On Board Dia
gnostic
(OBD
)
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU06.01.1

01-12
Depending on desired function Table
"Selectable functions", Page 01
-15
:

- Switch ignition on.
or

- Start engine.

- Press -Print- button to turn on Scan Tool (ST)
printer. Indicator lamp in button must light up.

- Press button 1 to select "Rapid data transfer"
operating mode 1. Rapid data transfer
HELP
Enter address word XX

When indicated on display
Note:
The address word 00 initiates the automatic test sequence, i.e. it results in
a DTC check on all OBD capable systems in the vehicle via rapid data
transfer.
- Press buttons -0- and -1- to select "engine electronics" and press -Q-
button to confirm input.
4B0906018Q
1.8 L R4/5VT
G 0008
Codin
g 07551
WSC 12345

VAG1551 Scan Tool (ST) display indicates control module identification,
e.g.
Pa
ge 14 of 19 On Board Dia
gnostic
(OBD
)
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU06.01.1

01-15
Selectable functions VAS5051 vehicle diagnostic, testing and information
system or VAG1551 Scan Tool (ST) Ignition
on,engine off Engine running
at idle Vehicle in
drive mode page
Address words
01 Engine electronics Yes Yes Yes Page
01
-10

00 Automatic test sequence Yes Yes Yes Page
01
-12

Functions
01 Check Control Module Versions Yes Yes Yes Page
01
-14

02 Check DTC Memory No Yes Yes Page
01
-16

03 Output Diagnostic Test Mode (DTM) Yes No No Page
01
-49

04 Basic Setting Yes Yes Yes Page
01
-58

05 Erase DTC Memory Yes Yes Yes Page
01
-16

06 End Output Yes Yes Yes Page
01
-18

07 Code Control Module Yes No No Page
01
-62

08 Read measuring value block Yes Yes Yes Page
Pa
ge 18 of 19 On Board Dia
gnostic
(OBD
)
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU06.01.1